Peak

• Fixing absorent floor and wall tiles out doors and in doors
• Fixing on heating floors
• Fixing poorly absorbent materials or non-absorbent materials such as single-fired tiles, refine porcelain stoneware and vitrified tiles
• Suitable for use when high performances are required, such as tile fixing in industrial environment or fixing on top of old ceramic tiles or natural stone indoors, in swimmingpools or on facades
• The tiles can be made of cotto, double fired, single fired ceramic

• Peak should be applied with a suitable toothed spreader, to be chosen according to the size and characteristics of the rear surface of the tiles. It is best to use the smooth part of the trowel to spread a fine initial layer, pressing down hard so as to obtain maximum adhesion to the substrate and to regulate water absorption, after which the thickness can be adjusted as required by tilting the spreader at an angle
• Spread the adhesive over a surface area which will allow for laying of the surface materials within the indicated open time and check for suitability of the adhesive at regular intervals, the open time may vary considerably during the same operation, depending on various factors such as exposure to sunlight, air currents, absorbency of the substrate, temperature and relative humidity of the atmosphere
• Press down each tile to allow for complete, uniform contact with the adhesive. In the case of laying in environments subject to heavy traffic or in outdoor locations, the double-spread technique must be used, to ensure 100% coverage of the rear of the tiles
• In general, ceramic tiles do not require preliminary treatment, however these materials should properly anchored to the substrate or which may modify the absorption characteristics of the tiles

• Colour : Grey & White
• Mixing Ration : 5.6 to 6.4 Ltrs/ Bag 20 Kg Peak
• Pot Life : ≥ 4 Hr
• Open Time : ≥ 30 Minutes
• Adjustability : ≥ 45 Minutes
• Bed Thickness : 3mm To 10mm
• Grouting : 8 Hours on wall / 24 hours on floor

20 Kg Bag.

12 Months with original packing in dry storage condition. Health & Saftey Precautions : Use Gloves. Non Toxic.

1. Prepare Peak in a clean container, first of all pouring in a quantity of water equal to approximately    of that which will be required.
2. Gradually add Peak to the water in the container, mixing the paste from the bottom upwards with a low-rev ( 400 RPM /min.) helicoidal agitator. Then add more water until the desired consistency is      obtained, the mixture must be homogeneous and without any lumps. For best results and to mix      larger quantities of adhesive, a stirring device with vertical blades and slow rotation is recommended.
3. Specific polymers with high-dispersion properties ensure that Peak is immediately ready for use.     The amount of water to be added, indicated on the packaging. It is possible to obtain mixtures with a     more or less thixotropic consistency, depending on the type of application.

Do not use on substrates with a gypsum and anhydrite base without use of HydroPrime the professional,  concentrated, water-base, surface insulation product

1. Heat-radiant slabs,
2. High-flexibility substrates;
3. Marble floor tiles and natural stone,
4. Metal and wood;
5. On old ceramic flooring,
6. On plasterboard;
7. On plastic or resilient materials,
8. On substrates which are wet, subject to moisture rising or in continuous contact with water.   

Do not use the adhesive to correct substrate irregularities greater than 10  mm

Shear Adhesion After 28 Days.                              ≥ 1 Mpa          ANSI A-118.1

Tensile Adhesion On Concrete After 28 Days.       ≥ 1 Mpa           EN 1348              

Durability Test:                                                       ≥ 1 Mpa           EN 1348

Adhesion After Heat Agening.                                ≥ 1 Mpa           EN 1348

Adhesion After Water Immersion                           ≥ 1 Mpa           EN 1348

Adhesion After Freeze Thaw Cycles                     ≥ 1 Mpa            EN 1348

Working Temperature From Conformity                C2 TE               EN 12004

                                                                               Type3T            IS 15477:2019

Approximately 55 to 60 sqft for 20 kgs bag with 6mm x 6mm square notch trowel for a bed of 3 mm