Products Wall Care Products Prime Putty

Prime Putty

White Cement Based Putty for Interior & Exterior

The least apparent and the most important part in any painting or photograph is its background. Dubond provides the perfect background for walls - be it in office or at your home. Paint away to glory and rest assured that Dubond will make it stick and stand out too.

Dubond promises you the perfect finish to interior decoration of all types. Be it corporate or home sweet home, Dubond is comfortable everywhere. Silently it works. Almost invisibly it creates the right backdrop that will help each drop of paint stand out with a character of its own.

DUBOND PRIME PUTTY is a white cement-based fine powder. It serves as filler/ leveller for walls and ceilings. It provides a waterproof surface with excellent smoothness, good adhesion, good breathing properties, and seals porosity for uniform deposition of finished paint and enhances durability. It helps you combine the suave look with beauty for interiors and exteriors. It can be used any type of surface like concrete, rendered wall, hollow block, precast walls, concrete ceilings, calcium silicate bricks etc. no need to apply any kind of primer on it before application of paint or distemper. It prevents the growth of algae and fungi on walls.


  • You don't require to mix pigment / stainer in DUBOND PRIME PUTTY
  • Quality of painted surface is directly proportional to quality of unpainted surface. DUBOND PRIME PUTTY gifts the ideal conditions necessary for a good paint job. The unpainted surface is just right for paint application after the use of Dubond PRIME PUTTY.
  • Paint can be applied on DUBOND PRIME PUTTY with or without the use of primer. Use of primer shall lend cost advantage in case of expensive paints.
  • Dubond PRIME PUTTY leaves a lustrous white and smooth surface which can also be left unpainted
  • Life of DUBOND PRIME PUTTY is as long as the life of grey cement plaster underneath.
  • It prevents growth of algae and fungus on walls.
  • Any kind of distemper can be applied on it directly
  • Textured finish can be obtained by use of texturing tools.
  • As prevalent in case of other non-cement putties, primer application is not recommended before applying DUBOND PRIME PUTTY. This saves cost.

Application Method

Surface Preparation

All the loosely-adhering and projecting material from the wall should be removed with the help of wire brush, putty blade or emery stone and clean water. New surface requires removal of dust, dirt and foreign matters. Cracks, voids and damages should be repaired. In the old, unpainted surface all loose material, organic, growth, dirt, dust etc must be first removed. Scrub the old painted surface with wire brush/ sand paper and clean thoroughly so that it is free from old paint/ dust particle till the cementations /plastered surface is seen. The wall surface should be moistened with sufficient quantity of water to saturate the surface as well as to clean the dust/dirt.

Preparation of DUBOND PRIME PUTTY paste

Mix DUBOND PRIME PUTTY slowly in 35 -40 % by volume in clean water to prepare paste. Mix vigorously for 10 -15 minute to get lump free and uniform paste.

Application of DUBOND PRIME PUTTY on the surface
  • First coat of the mixed DUBOND PRIME PUTTY should be applied on an already-moistened wall/surface from bottom to upward direction with the help of putty blade / trowel.
  • Allow the surface to dry for at least 3 hours and then apply second coat of putty. Leave the surface to dry completely.
  • After drying of first coat of putty just rub the surface gently with a putty blade in order to remove loose particles.
  • After drying of second coat remove marks if any with the help of moist sponge or rub surface very gently with the putty blade.
  • Leave the surface to dry preferably for overnight.
  • Always prepare a required quantity of putty and use it within 2 -3 hours of mixing with water.
  • Maximum two coats of DUBOND PRIME PUTTY.
  • Maximum thickness of the coats (layer) should be 1.5mm.

The coverage area of DUBOND PRIME PUTTY on smooth normal mortar wall is 20 to 25 sq. ft/kg in double coat. The coverage area will depend upon the quality of the surface and construction.

Precaution during application
  • Mixing of DUBOND PRIME PUTTY is very important and care to be taken for proper mixing with hand or mechanical stirrer.
  • Ensure that surface is plastered or made with cementatious material.
  • Ensure the surface is totally clean and is moderately rough.
  • Ensure that surface is just wet. Over wetting resulting in accumulation of water on surface should be avoided.
  • Although it contains non toxic materials, use rubber gloves while mixing. In case of contact with eyes or mouth, wash with plenty of water.
  • Keep the product out of reach of children.
  • People allergetic to cement should take proper precautions.
  • Once putty paste has hardened it should not be reused by adding water.
Technical specification
Compressive Strength (28 days) 14.00 N/mm2
Surface Hardness 3.10 N/mm2
Tensile adhesion (28 days) 2.69 N/mm2
Water demand 30-35% by volume (depending on weather and site needs)
Pot life 2 to 3 hours
Maximum Thickness (two coat) 1.5mm
Coverage ( On smooth surface) 25 to 35 sq. ft. per 1 kg
Packaging 1 kg., 5 kg and 20 kg packs.
Storage Store in dry moisture free area. Storage life is 6 months
Safety Use gloves. Non toxic.

The information given in this leaflet is for general guidance only. Specific instructions for various site conditions can be provided on demand.

Dubond Quality Products

Looking for DUBOND products now

call us on +91 93771 77771 today!